Thiết bị Bosch
091 221 3533
Máy ra vào lốp
097 488 5125

Thiết bị kiểm tra góc đặt bánh xe BOSCH FWA-4630

Thiết bị cân chỉnh góc đặt bánh xe BOSCH FWA-4630, công nghệ mới nhất hiện nay !
Thông số kỹ thuật
Thiết bị kiểm tra và cân chỉnh góc đặt bánh xe 3D Bosch - Đức
Model : FWA 4630
Hãng sản xuất : Bosch - Đức
Thông số đo:
- Các góc đo chính như sau:  
- Góc Total Toe (trục trước và sau): +/- 2, Độ chính xác:+/- 3’   
- Góc Toe riêng (trục trước và sau): +/- 2 , Độ chính xác:+/- 2’ 
- Góc Camber (trục trước và sau): +/- 3 , Độ chính xác:+/- 2’   
- Góc Set back (trục trước và sau): +/- 2 , Độ chính xác:+/- 2’
- Góc Castor: +/- 18 , Độ chính xác:+/- 4’         
- Góc Kingpin: +/- 18 , Độ chính xác:+/- 4’         
- Góc Toe khi đánh lái: +/- 20 , Độ chính xác:+/- 4’
  • Thông số kỹ thuật
  • Mô tả chi tiết
  • Hướng dẫn sử dụng
  • Tài liệu
Model : FWA 4630
Hãng sản xuất : Bosch - Đức
Thông số đo:
- Các góc đo chính như sau:  
- Góc Total Toe (trục trước và sau): +/- 2, Độ chính xác:+/- 3’   
- Góc Toe riêng (trục trước và sau): +/- 2 , Độ chính xác:+/- 2’ 
- Góc Camber (trục trước và sau): +/- 3 , Độ chính xác:+/- 2’   
- Góc Set back (trục trước và sau): +/- 2 , Độ chính xác:+/- 2’
- Góc Castor: +/- 18 , Độ chính xác:+/- 4’         
- Góc Kingpin: +/- 18 , Độ chính xác:+/- 4’         
- Góc Toe khi đánh lái: +/- 20 , Độ chính xác:+/- 4’
máy cân chỉnh góc đặt bánh xe

Measuring options:
Total toe (front axle + rear axle)
Partial toe (front axle + rear axle)
Camber
Wheel offset (front axle + rear axle)
Driving angle between axles
After-run
Kingpin angle
Relative steering angle Only for standard alignment
After-run correction range
Lateral offset left/right
Wheel track differential
Axle offset (front axle + rear axle)
Steering wheel angle max. Steering wheel angle not possible for all vehicles
Wheel base differential
The check is carried out on cars and light trucks with a weight of up to 3.5 t and a wheel base of 180 cm to 340 cm (wheel alignment is possible on vehicles up to 430 cm using larger boards at the rear, which are available as special accessories.
Use in automobile workshops and tire service centers with a high throughput of wheel alignments.

OEM recommendations worldwide
Vehicle specs database: as standard with over 150 vehicle manufacturers (approx. 40,000 data sets) including adjustment diagrams – directly from the vehicle manufacturer
Maximum operational efficiency thanks to a choice of three measurement routines: program-guided, quick alignment, random access for testing of individual values
Device components are designed to be extremely easy to use.
ISO certification of testing station through calibration in the field.
Simple, intuitive operation, including for workshop staff without specialist knowledge of wheel alignment and the simple runout compensation means it can be performed by just one person.
Software: maximum efficiency thanks to a choice of three measurement routines: program-guided, quick alignment or random access for testing of individual values.
Extremely short wheel alignment time: seven minutes to printout of results. As the image capture frequency is very high, measurements can be taken almost in real time.
The steering wheel angle for the after-run angle, kingpin angle, and relative steering angle is determined using cameras. Total steering wheel angle measurement depending on the distance up to 50° performed using cameras.
The mobile device is easy to stow in vehicles and quick to use (short setup times) and can be employed out and about at different testing stations.
Robust trolley for the most important components: Control system computer, TFT monitor, color printer, all recording devices practically stowed
Simple and flexible user software

Technical data: FWA 4630
Power supply 110 - 240 V AC (10 A)
Voltage 10 A
Frequency 50/60 Hz
Power 500 W
Trolley with recording device (W x H x D) 1520 x 1180 x 770 mm
Trolley without recording device (W x H x D) 1520 x 880 x 770 mm
Recording device (W x H x D) 150 x 370 x 650 mm
Weight recording device 9.3 kg
Weight 110 kg


Accesories
Standard aluminum mechanical turntables without aluminum filler pieces (1 unit) (1 690 702 157)
Rubber cover for aluminum turntable (1 unit) (1 690 402 001)
Drive-on ramp set for two aluminum turntables (1 690 701 052)
Magnetic holder (1 690 701 051)
Universal quick-action clamp 10"-21" (1 unit) (1 690 311 001)
Multi-quick clamp – clamping range 14" to 24" (1 unit), quantity required: 4 (1 690 501 250)
Attachment bolts 100 mm (12 units) (1 690 302 008)
Distance bolts for Mercedes-Benz and BMW for the multi-quick clamp (set: 5 units per clamp) (1 690 401 019)
Lift adapter swivel foot, short (1 690 701 047)
Lift adapter swivel foot, long (1 690 701 020)
Mine adaption for recording device (1 690 701 027)
Step-bracket set (2 units) (1 690 701 045)
3D standard instrument panel (quantity required: 4) (1 690 711 005)
Keyboard (English) (1 687 022 368)
Data transmission/charging station (1 693 770 003)
Brake pedal lock (1 690 401 006)
Steering wheel lock (1 690 401 007)
Ballast bag (5kg) (1 693 740 001)

Scope of delivery
2 recording devices
Switch
Hub
Test box
Trolley
19" monitor
Printer
Program
Specified data (cars and vans)
Dongle (USB)
Licenses
Standard boards (4 units)
Steering wheel lock
Brake pedal lock